Dual Feed Fuel Inlet & Filter Kit For Thunder Series AVS Carbs
||Edelbrock Thunder Series AVS
STAINLESS STEEL BRAIDED FUEL LINE KITS
For Racing Fuel Pump to Regulator Kits
Connects mechanical racing fuel pumps to the Edelbrock Fuel Pressure Regulator Kits. Made of the highest quality materials. Pre-assembled hose with hose ends. Fits 1/2” NPT outlets and 3/8” NPT inlet fuel line.
FUEL PUMP TO CARB INLET HOSE KITS
These high-quality fuel line kits offer a clean and precise fuel supply line for mechanical fuel pumps with 3/8” NPT outlet to Edelbrock Single-Feed or Dual-Feed fuel inlet kits #8128, #8131, #8133, and #8134. These hose kits are pre-assembled hose with hose ends and are available with stainless steel braided hose or black nylon fabric ProClassic hose.
FUEL PUMP TO CARB HOSE KITS
These high-quality fuel line kits offer a clean and precise fuel supply line for mechanical fuel pumps with 3/8” NPT to the 5/8” -20 fuel inlet on Edelbrock Performer Series and Thunder Series AVS Carbs. They are manufactured with Russell ProClassic hose and include fuel filter, 5/8” -20 banjo bolt and gaskets. Will not work with OEM or equivalent fuel pumps.
SINGLE FEED FUEL INLET AND FILTER KITS
These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The #8126 includes a barbed end for a push-on 3/8” rubber fuel line. The #8131 and #8134 include an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an Edelbrock fuel line kit for a complete fuel-pump to carburetor plumbing solution. They are manufactured of chrome plated steel and include a 5/8” -20 threaded banjo bolt with gaskets.
DUAL FEED FUEL INLET AND FILTER KITS
These dual feed fuel inlets are designed specifically for Edelbrock Thunder Series AVS carburetors. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. Options include a barbed end for a push-on 3/8” fuel line or -6 AN aluminum fuel filter with a 40 micron filter element. Match with Edelbrock fuel line kit for a complete fuel-pump to carburetor plumbing solution. They are manufactured of chrome plated steel and include a 5/8” -20 threaded banjo bolt with gaskets.
DUAL-QUAD FUEL HOSE KIT
Supplies fuel to two Edelbrock carbs when used on Edelbrock Dual-Quad manifolds. Use with a fuel hose kit such as our #8122 or #8127. 6-7/16” center-to-center, 1/8”-NPT fuel pressure port and a 3/8”-NPT fuel inlet.
UNIVERSAL SINGLE-FEED FUEL HOSE & FILTER KIT
Designed for quick installation when retaining part of the stock steel fuel line, simply cut the stock line and install the compression fitting. Use supplied neoprene hose, clamp and special fuel filter and connect to carb. Will work with either 5/16” or 3/8” lines. Kit includes fuel filter, special fittings to adapt 5/16” and 3/8” steel line to 3/8” fuel hose, 24” of 3/8” fuel hose (SAE 30R7) and four stainless steel worm-type hose clamps.
UNIVERSAL DUAL-FEED FUEL HOSE & FILTER KIT
Made from aircraft quality buna-N neoprene hose encased in braided stainless steel, this fuel line kit is temperature, gas and oil resistant. Made for 3/8” NPT fitting, the fuel line is adjustable between the carb bowls from 7-1/2” to 11-1/2”. Includes 1/8” pipe fitting, plug for fuel pressure gauge, etc. Hose nipple not included.